FREE | 1 May 2021 | 33.6 MB
这是“ BUSTER”的老大哥,它有大量的改进和新功能!
经典的控制台压缩器,带有额外的滤波器和瞬态侧链选项,可控制整个信号!
特点
立体声压缩机:压缩机部分
FLT:过滤器部分
TR:瞬态部分
控制:控制部分
压缩机部分
-阈值(dB):+15至-15-
攻击(ms):0.1、0.3、1、3、10、30-
释放(秒):0.1、0.3、0.6、1.2,自动
-比率:
1.5、2、3、4、5、10-补足(dB):0至15-
混合(%):干燥至WET
过滤器部分(侧链) ) -HPF
(Hz):20至500
-MID(〜1500Hz):-6dB至+ 6dB
-HF(〜10kHz):0dB到-10dB *将像著名的光管压缩器一样工作,可以帮助您更好地控制高频。
瞬态部分(侧链)
-BOOST(dB):0到10 *在增强攻击的同时,它将减少信号的衰减/释放,从而使压缩器仅在攻击/峰值时更加敏感。
-倾斜(〜1kHz中心):-6dB至6 dB *放置在BOOST之前,仅将专用范围发送到BOOST。因此,BOOST仅会影响给定的频率范围,并且只会增强该范围的瞬变。如果默认为TILT,则BOOST将影响整体瞬态。
-混合(%):从干到湿*将混合干和湿信号。增强瞬变之后,您可以与DRY信号混合以保持减少的信号释放。当MIX处于默认位置时,TR处于关闭状态。因此,您可以一直旋转MIX旋钮以啮合TR部分。
* EXT(外部侧链):当您使用EXT时,侧链电路将监听传入的信号,您可以在传入的信号上使用“过滤器”和“瞬态”部分。
控制部分
-MAIN:通用旁路
-TURBO:Turbo Mod * Turbo mod将帮助压缩器影响整个信号范围。否则,压缩器将专注于中频。添加此mod可以保留硬件的原始符号。
-XFORMER:输入/输出变压器*如果您使用XFORMER,输入/输出IC将被替换为变压器以平衡它。这将影响阻抗,特性,整体声音。
-ANALOG OBSESSION LOGO:过采样。进行过采样时,它将变为红色。另外,向您显示一条通知。
可用格式
VST / VST3 / AU | Mac 10.9-11.X
VST / VST3 | Windows
7-8-10此更新将合并BUSTER和BUSTERse。现在,只有“ BUSTERse”。
1/5/2021-v6.2.0更新
-具有更近的硬件指纹的改进的DSP-
4倍过采样功能
-Retina / HiDPI-
为旋钮增加了读出功能
Here is big brother of “BUSTER” with tons of improvements and new features!
Classic console compressor with extra Filter and Transient sidechain options to dominate whole signal!
FEATURES
STEREO COMPRESSOR : Compressor Section
FLT : Filter Section
TR : Transient Section
CONTROL : Control section
Compressor Section
– THRESHOLD (dB) : +15 to -15
– ATTACK (ms) : 0.1, 0.3, 1, 3, 10, 30
– RELEASE (sec) : 0.1, 0.3, 0.6, 1.2, Auto
– RATIO : 1.5, 2, 3, 4, 5, 10
– MAKE UP (dB) : 0 to 15
– MIX (%) : DRY to WET
Filter Section (Sidechain)
– HPF (Hz) : 20 to 500
– MID (~1500Hz) : -6dB to +6dB
– HF (~10kHz) : 0dB to -10dB *Will work like famous optical-tube compressor and help you to control high frequencies, better.
Transient Section (Sidechain)
– BOOST (dB) : 0 to 10 *While boosting attack, it will reduce decay/release of signal to make compressor more sensitive with only attacks/peaks.
– TILT (~1kHz Center) : -6dB to 6 dB *It’s placed before BOOST to send only dedicated range to BOOST. So, BOOST will affect only given frequency range and will boost only this range’s transients. If TILT is default, BOOST will affect overall transients.
– MIX (%) : DRY to WET *Will blend DRY and WET signal. After boosting transients, you can blend with DRY signal to keep reduced release of signal. When MIX in default position, TR is off. So, you can turn MIX knob to all the way up to engage TR section.
*EXT (External Sidechain) : When you engage EXT, sidechain circuit will listen incoming signal and you can stil use Filter and Transient sections on incoming signal.
Control Section
– MAIN : General Bypass
– TURBO : Turbo Mod *Turbo mod will help to compressor to affect whole signal range. Otherwise, compressor will focus on mid frequencies. This mod added to keep original sign of hardware.
– XFORMER : In/Out Transformers *If you engage XFORMER, in/out ICs will be replaced with transformer to balance it. This will affect to impedance, character, overall sound.
– ANALOG OBSESSION LOGO: Oversampling. It will turn to red when oversampling is engaged. Also, show you a notification.
Available Formats
VST/VST3/AU | Mac 10.9 – 11.X
VST/VST3 | Windows 7 – 8 – 10
This update will combine BUSTER and BUSTERse. Now, there is only “BUSTERse”.
1/5/2021 – v6.2.0 Update
– Improved DSP with closer hardware finger-print
– 4x Oversampling Feature
– Retina/HiDPI
– Added Readout Feature for knobs